Hardness test instrument accessories

Hardness testing software

Is designed to fully clear and degree of automation to simplify and hardness testing industries within the territory of one of the most complex hardness test requirements.

  • The preferred application design in advance
  • Advanced workflow control
  • Enhance the report

Struers provides a wide range of additional software module, these modules can be added to the Duramin hardness tester software

Can complete a simple test in 3 seconds, and can be done in ten minutes for the first time spend hours and hours on a sample to map the test, then in 1 minutes to complete each repeat, all of which are based on a user management system, to maximize across multiple operators of repeatability and reproducibility.

Additional software module is available.

  • Weld detection module
  • Fracture toughness (Kc) module
  • Barrel test module
  • CHD test module
  • Test point editor
  • (take off) carbon test according to ISO898-1
  • Remote control module
  • Automatic edge detection
  • Automatic contour scanning
  • Automatic mapping module
  • Q - DAS certificate connection protocol
  • Duramin practical software
  • CHD test module.XY objective table manually
  • Test point editor.Duramin - 40 m
  • Drawing and testing module
  • Image matching module
  • Force/depth/time figure
  • Tap measure (ISO2702)

    If you need more information about the hardness testing software, please contact us.

    Duramin hardness tester software modules

    Weld detection module

    Special welding hardness testing module, used to according to the base material, the heat affected zone (HAZ) and weld zone defined patterns.

    • Customizable mode, can adapt to any weld geometry.
    • Allow along the fusion line accurate positioning indentation, and surface specific distance apart (according to international standards).

    Fracture toughness (Kc) module

    The module is used for using Nihara formula to measure the fracture toughness KIc.

    • With the help of a magnifying glass tools, you can easily identify the crack tip.
    • The formula for different Palmqvist and Median fracture model.

    Barrel test module

    The module is used for testing according to the requirements of the arms industry shell/shell.

    • Used to along the barrel length of more of the indentation data management easily.

    CHD test module

    Used in CHD with automatic slide of machine test module.Enable the CHD, SHD and NHD test mode.

    • Used for surface treatment of the sample testing, analysis and reporting of rapid setting.
    • By means of "edge detection" function, easily locate perpendicular to the surface of indentation pattern.
    • Automatically terminate the test to reduce the test duration and save time.

    Test point editor

    The module is used for on the tester with electric objective table definition and set up the basic test mode (straight lines, squares, sawtooth, triangle).

    • Create a simple design in a few seconds.
    • Can set up multiple patterns with automatic test for multiple samples.

    (take off) carbon test according to ISO898-1

    The module is used for testing and analysis of fasteners, threaded, ISO 898-1 for three models to find the right test position.

    • Automatic thread contour detection.

    Remote control module

    The module is used for using TCP/IP remote control hardness tester.

    • Communication interface.
    • This module allows the use of TCP/IP communication protocol remote control HAT.

    Automatic edge detection

    Edge detection module, used to create the design of parallel to the edge of the test sample.

    • For use in certain distance and Angle relative to the sample outline quickly locate indentation.
    • Used for the surface hardness and depth of hardening for automatic analysis of the widely.

    Automatic contour scanning

    The module is used for scanning the sample complete contour.

    • In a few seconds to build the 2 d model of the sample.
    • Allowed to enable area hardness mapping.

    Automatic mapping module

    The module is used for the area or scan on the contour map of 2 d or 3 d hardness.

    • To create the entire surface of the color chart, allowing identification of the hardness change and the critical point in the samples.
    • Is well suited to infer that the mechanical properties of the material on the surface.

    Q - DAS certification.Connection protocol

    The module is used for in QDAS format (Aq def or Dfd/Dfx) export test results.

    • Very suitable for implementation in the large test facilities.
    • For efficient data management and tracking complex data sets.

    Duramin practical software

    This module is used to test results, scale and time stamp the external, computer direct export to Microsoft Excel.

    • It allows real-time export raw data, in order to customize the data post-processing.
    • Very suitable for need to remote data storage and analysis laboratory.

    CHD test module.XY objective table manually

    The module is used for CHD, the commissioning of the manual stage SHD, NHD mode.

    • Very suitable for do not need to simple object stage of hardening depth test automatically.

    Test point editor.Duramin - 40 m

    The module is used for the manual cargo platform to create a test point mode (including + CHD, SHD, NHD).

    • Even in the manual on the slide can also be a complex test.

    Drawing and testing module

    The module is used for the simple hardness testing (distance and Angle) comments and manual testing.

    • No need for external microscope and software can be rapidly and accurately detect the surface.
    • Just click a few times, can save the measured values and include them in the report.

    Image matching module

    The module is used for scanning and joining together to get an overview of the complete object stage or detailed image of the test sample a large area.

    • Very suitable for large samples, such as large weld and large mechanical components.
    • No need for an external microscope and extra wide Angle lens.

    Force/depth/time figure

    The module is used to display the indentation force/depth/timing diagram (only applicable to which has the function of Rockwell tester).

    • When need advanced control on loading conditions.

    Tap measure (ISO2702)

    The module is used for according to ISO 2702 (take off) carbide parts thread measurement of automatic test.

    • Allowed to choose screw type in order to test according to ISO 2702.